Woodluxe Wood Stain Remover (015)

Original price was: $69.99.Current price is: $65.88.

An innovative exterior wood stain remover designed to stains and finishes from exterior wood surfaces

  • Removes both latex and alkyd stains that are flaking or peeling
  • Gets down to the healthy wood
  • Fast-acting formula
  • Removes clear finishes of solid color stains


Remove, Finish Remover 315
Benjamin Moore & Co., 101 Paragon Drive, Montvale, NJ 07645 Tel: (201) 573-9600 Fax: (201) 573-9046 M72 315 US 102518
Benjamin Moore and the triangle “M” symbol are registered trademarks, licensed to Benjamin Moore & Co. © 2008, 2018 Benjamin Moore & Co.
All rights reserved
Surface Preparation
Project surfaces may be damp or dry. Do not apply if surface temperature is below 50°F (10°C). Protect adjacent surfaces; cover with plastic and/or tape off any areas not being stripped. Pre-wet and/or cover vegetation; rinsing residue will not harm plants or roots. Exposure to concentrate may burn foliage.
It is recommended that you test product performance in an inconspicuous area prior to use.
PRIOR TO APPLICATION: Determine proper dilution following the chart below. Test a small, inconspicuous area and allow to dry before general use. Before and after application, liberally spray surrounding plants and vegetation with water. Avoid contact with metal, lawn furniture and fabric. If necessary, protect adjacent surfaces with plastic.
Product does not control mold, mildew, fungus or algae, only removes stains.
WARNING! If you scrape, sand or remove old paint, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator to control lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the National Lead Information Hotline at 1-800-424-LEAD or log on to
MIXING: Remove, Finish Remover is a concentrate. This container makes up to 5 gallons of product.
Multiple Coats / Solid Color or Semi Solid Stain
Weathered / Solid Color or Semi Solid Stain
Semi Transparent Stain
Transparent Stain
Clear Finish
Do not dilute
Mix 1 gallon of REMOVE
with 1 gallon of water
Mix 1 gallon of REMOVE
with 2 gallon of water
Mix 1 gallon of REMOVE
with 3 gallon of water
Mix 1 gallon of REMOVE
with 4 gallon of water
1. Apply product liberally to surface with plastic garden sprayer, brush or roller.
2. Allow solution to stand for 10-30 minutes, depending on age and type of finish to be removed.
3. Agitate with stiff bristle brush in direction of wood grain and rinse using a garden hose with nozzle or power washer.
4. Neutralize surface with Brighten, Brightener & Neutralizer (317) following label directions.
5. Allow to dry thoroughly. Note: When applying to vertical surfaces, apply from bottom to top.
CAUTION: Project surfaces will be extremely slippery.
Mix according to the instructions above.
CLEAN UP: Clean equipment with warm, soapy water.
DISPOSAL: USE COMPLETELY OR DISPOSE OF PROPERLY. Local disposal requirements vary; consult your sanitation department or state-designated environmental agency for local disposal options.
Environmental Health & Safety Information
Contains: Sodium Hydroxide and Sodium Metasilicate
CORROSIVE. CAUSES SEVERE BURNS TO EYES AND SKIN. MAY BE FATAL IF SWALLOWED. Contact with eyes may cause severe burns with possible corneal damage and blindness. Contact with skin may cause chemical burns or dermatitis. Vapors and mist may cause irritation to eyes and respiratory tract. Ingestion may cause gastrointestinal corrosion, vomiting, diarrhea, shock or death.
Use only with adequate ventilation. Do not breathe vapors, spray mist or sanding dust. Avoid contact with eyes and prolonged or repeated contact with skin. Wear eye protection or face shield. Wear butyl gloves, impervious apron, boots and other clothing if needed to prevent contact. If spraying (only outdoors) use a NIOSH approved respirator. If you experience eye watering, headaches or dizziness increase fresh air or wear a properly fitted vapor/particulate NIOSH approved respirator during application, sanding and clean up. Follow respirator manufacturer’s directions for use. DO NOT MIX OR USE with other household cleaners or chemicals. Close container after each use. Wash thoroughly with soap and water after each use. Exercise caution when working on surfaces that are wet, especially from cleaner. Wet surfaces are extremely slippery. WARNING Cancer and Reproductive Harm–
FIRST AID In case of eye contact, immediately flush with water for 30 minutes while lifting upper and lower lids. In case of skin contact, wash with soap and water immediately, remove contaminated clothing and launder before reuse. If affected by inhalation of vapors or spray mist, remove to fresh air. If ingested and victim is conscious give one glass of water or milk to dilute. DO NOT INDUCE VOMITING. Never give anything by mouth to an unconscious or convulsing victim. In all cases of exposure, call a physician immediately.
SPILL – Absorb with inert materials and dispose of as specified under “DISPOSAL”.
Refer to Safety Data Sheet for additional health and safety information.

TDS Sheet